OrionPilot 403 V2

$42.99

Tax included. Shipping calculated at checkout

Select fc

Only FC Only FC
55A AM32 Stack 55A AM32 Stack
60A Bluejay Stack 60A Bluejay Stack

Select firmware

Ardupilot Ardupilot
PX4 PX4

Product variants

Select quantity

Description

Specifications

MCU: STM32H743VIH6, 480MHz, 2MB Flash
IMU: BMI088+BMI270
Baro: SPL06
Compass: QMC5883L
OSD: AT7456E
MicroSD Card Slot
8x UART
11x PWM
1x I2C
1x SWD
2x ADC (VBAT, Current)
USB Type-C
DJI O3/O4 VTX connector
BEC 5V 3A output (for controller, receiver, GPS, optical flow or other devices)
BEC 12V 3A output (for video transmitter, camera)
Bluetooth Telemetry (connected to UART8 internally, baudrate 115200)
VBAT Input Range: 2-6S (6-27V)

UART Mapping (Ardupilot)

SERIAL0 -> USB
SERIAL1 -> UART1 (MAVLink2, DMA-enabled)
SERIAL2 -> UART2 (DisplayPort, DMA-enabled)
SERIAL3 -> UART3 (GPS, DMA-enabled)
SERIAL4 -> UART4 (MAVLink2, DMA-enabled)
SERIAL5 -> UART5 (DMA-enabled)
SERIAL6 -> UART6 (RCIN, DMA–enabled)
SERIAL7-> UART7 (ESC Telemetry, DMA-enabled)
SERIAL8 -> UART8 (DMA–enabled, connected to on board BlueTooth Telemetry)

UART Mapping (PX4)

ttyACM0->USB
ttyS0->TELEM1 -> UART1
ttyS1->GPS2 -> UART2
ttyS2->GPS1 -> UART3
ttyS3->TELEM2 -> UART4
ttyS4->TELEM3-> UART5
ttyS5->RC -> UART6
ttyS6->URT6 -> UART7
ttyS7->TELEM4/SERIAL4 -> UART8

RC Input (Ardupilot)

The UART6 is compatible with all ArduPilot supported receiver protocols.

PPM is not supported.
SBUS/DSM/SRXL connects to the RX6 pin.
FPort requires connection to TX6 . See FPort Receivers.
CRSF also requires a TX6 connection, in addition to RX6, and automatically provides telemetry.
SRXL2 requires a connection to TX6 and automatically provides telemetry. Set SERIAL6_OPTIONS to “4”.

Any UART can also be used for RC system connections in ArduPilot and is compatible with all protocols except PPM. See Radio Control Systems for details.

OSD Support (Ardupilot)

The OrionPilot 403 v2 supports onboard OSD using OSD_TYPE 1 (MAX7456 driver). Simultaneously, DisplayPort OSD is available on the HD VTX connector, See below.

VTX Support

The SH1.0-6P connector supports a DJI Air Unit / HD VTX connection. Protocol defaults to DisplayPort. Pin 1 of the connector is 12v so be careful not to connect this to a peripheral requiring 5v.

PWM Output

The OrionPilot 403 v2 supports up to 11 PWM outputs.

Channels 1-8 support DShot and bi-directional DShot.

(currently PX4&INAV not support BDShot function)

PWM output share grouped and every group must use the same output protocol:

1,2,3,4 are group 1

5,6 are group 2

7,8,11 are group 3

9,10 are group 4

Note: PWM11 is the “LED” pin. If this is configured for serial LED use then PWM 7 and 8 can only be used as serial LED also.

Battery Monitoring

The board has a internal voltage sensor and connections on the ESC connector for an external current sensor input.